Дом Продукты Z-образный складной контейнерный дом Складной контейнерный дом, изготовленный на заказ по OEM-заказу, Z-образного типа, в разобранном виде.

bulk portable folding container house z type front blue door

sample portable folding container house z type front window bar 86 webp

Z-образный складной контейнерный дом

Складной контейнерный дом, изготовленный на заказ по OEM-заказу, Z-образного типа, в разобранном виде.

A Z type leaves the line at 5800 × 2500 × 2430 mm and folds to 390 mm. On a custom order the folding geometry stays and the parts around it change: core, skin gauge, glazing, socket layout and colour. This unit is built to a nominated revision, and the drawing that ships with it is stamped with that revision.

технические характеристики продукта	20 футов
материал	Оцинкованная сталь, нержавеющая сталь 304
наполнитель	минеральная вата, пенополистирол и полиуретан
Диапазон рабочих температур	от -30°C до +70°C
Настройка	стеновые панели, напольные панели, розетки, мебель, водопроводные трубы, кухонные шкафы, сантехника и так далее.
Местоположение завода	ГУАНЧЖОУ

Поддерживаемые условия доставки	EXW, FCA, FOB, CIF, DDP
Условия оплаты	Банковский перевод (T/T), аккредитив (L/C), другие условия обсуждаются.

Запросить информацию сейчас

Делиться:

Описание продукта

Span, Packed Depth and Ordered Mass

Open, a custom z type folding container house measures 5,800 mm by 2,500 mm, and the pad has to carry that footprint exactly. That is about 14.5 m² of floor, with 2,430 mm of internal height, so a standing adult clears the ceiling. Folded, the pack sits 390 mm deep and stacks on a flat rack. Weight runs 1,100 kg on a standard build and 1,180 kg when the panel order gets thicker. The crane, the lorry and the pad all follow from those numbers.

Элемент	Стандартная сборка	What an OEM order can move it to	Fixed at
След	5800 × 2500 × 2430 mm	Length 5800 to 6000 mm, width to 2500 mm only	Steel cut
Folded thickness	390 mm	430 mm if walls go to 75 mm, which costs one set per 40HQ	Ламинирование панелей
Unit weight	1100 kg	1180 kg with a 75 mm core, 1040 kg with EPS	Ламинирование панелей
Секция рамы	столбик 63 × 80 × 1,5 мм	2.0 mm wall on the six folding posts only	Tube mill
Столбец	150 × 62 × 1.5 mm U-groove	2.0 mm, or 160 mm depth for a second storey	Steel cut
Стенка сердцевины	Минеральная вата 50 мм, 65 кг/м³	75 mm wool, EPS at 12 kg/m³, or PU at 40 kg/m³	Ламинирование панелей
Стенка кожи	цветная сталь 0,28 мм	0.35 mm, wood grain, matte, or a printed wrap	Coil order
Крыша	1040 tile 0.45 mm, 30 mm wool	75 mm roof panel, or a standing seam profile	Coil order
Пол	15 mm MGO, 1.6 mm wear layer	18 mm cement board, SPC, or a plywood deck	Panel layup
Дверь	970 × 1970 mm aluminium anti-theft	840 × 2030 с более крупным планом или с двойным листом	Frame weld
Windows	2 × 870 × 1215 мм скользящий	3 or 4 openings, awning, fixed, or full height	Frame weld
Электрики	1 breaker, 3 sockets, 5 LED lights	Circuit split, 110 or 220 V, external inlet	Wiring
Insulation value	About R 1.3 for the 50 mm wall	R 1.9 at 75 mm, R 2.1 with 50 mm PU	Ламинирование панелей
Цвет	Одно порошковое покрытие RAL	One colour as standard, two tones when ordered	Powder coat
Маркировка	Только маркировка для отправки	Numbers stencilled for routing across a site	Упаковка
Документы	Счет-фактура, упаковочный лист, коносамент, сертификат происхождения.	Paperwork that clears customs without a delay	Before loading
Minimum run	1 единица	10 units for a dedicated lamination run	Order
Lead time	15 to 20 days	25 to 30 days once the coil is ordered	Coil order

Installation video

Tube Sizes, Panel Skin and Core

Square tube comes in two wall thicknesses, 2.0 mm on the main beams and 1.5 mm through the cross members and braces. A 160 mm sill beam carries the floor deck. At each corner stand 100 mm posts. Hinge barrels run stainless and bolt through a 200 mm plate. Every tube end gets capped and sprayed with cold galvanizing before paint.

Chassis schedule
· 2.0 mm galvanized main beam along each long side
· 1.5 mm cross members under the floor deck
· 160 mm sill beam with a folded top lip
· 100 mm corner posts, four to a unit
· 200 mm hinge plate in stainless steel

Outside, a custom z type folding container house carries 0.28 mm colour steel, with a 0.35 mm liner facing the room. A 50 mm core sits between them, bonded across the full face with a two part adhesive. Roof panels follow the same build, and the floor deck is 15 mm board. Panel edges fold into a lip that takes a gasket. Two people carry one finished panel by hand.

Panel and deck build
· 0.28 mm steel skin on the outer face
· 0.35 mm liner on the room side
· 50 mm insulated core, bonded full face
· 15 mm floor deck under a wear sheet
· Folded edge with a rubber gasket seat

Main Board, Ceiling Lights and Sockets

Wiring runs through the panel voids and terminates at marked boxes. Inside sit a main switch, an earth leakage trip and spare ways for the circuits that will be added later on site. Lamps and sockets sit on separate circuits. Heights for every switch follow the drawing agreed at order. An outside socket and a light over the door can join the same loom.

Электрокомплект
· Distribution board with spare ways
· Leakage trip on the socket ring
· Ceiling lamps on a switched circuit
· Wall sockets at drawing heights
· External light over the entry door Spare ways sit in the board for the circuits that will be added later on site, and an outside socket plus a light over the door can join the same loom.

Erection Steps and Site Labour Needs

Once the pack is on the pad, erection needs no crane. Four workers cut the banding, lift the roof frame and stand the long walls, with pins dropping into the corners behind them. Roof cams draw the seam closed. End panels slide into their channels, and the door is checked for swing. The drawing carries a crew through the next unit.

Crew hand tools
· Banding cutter and a rubber mallet
· Podger bar for the corner pins
· Spirit level for the pad
· Sealant gun and two spare nozzles
· Touch up paint in the RAL shade

Crate Packing, Export Papers and Field Use

Flat, a custom z type folding container house stacks into a 40HQ at 50 mm wall thickness. Timber cradles take each unit and film wraps the pack. For a long sea leg, desiccant bags go inside before the wrap closes. Lifting points stay clear of the film, so a crane hook can still reach them. Outside marking matches the packing list and the frame stencil.

Packing list
· Timber cradle under each corner
· Shrink film over the folded pack
· Desiccant bags inside the wrap
· Corner guards on the castings
· Packing list in a weatherproof pouch

Documents ride with a custom z type folding container house: invoice, packing list, bill of lading and certificate of origin. Mill certificates, test reports and stamped drawings can join an OEM order. At the plant, spares cover pins, roof cams, sash rollers and lock barrels. The same body takes work as an office, a spare room, a clinic bay or a staff cabin.

Производственный процесс в цехе

Ввод в эксплуатацию завода

Мы являемся профессиональным производителем, специализирующимся на сборных контейнерных домах, расширяемых контейнерных домах, складных контейнерных домах и мобильных сборных ванных комнатах. Мы проектируем, производим и экспортируем модульные жилищные решения для отелей, вилл, офисов, общежитий, складов, мастерских и строительных площадок. Наш завод занимает площадь 50 000 квадратных метров и расположен в Гуанчжоу. Приглашаем вас посетить наш завод.

Теги:

Custom OEM Z Type Container House flat packed folding container house z type folding container house

Складные контейнерные дома, заводская поставка, Z-образный тип, оцинкованная сталь.

Складной контейнерный дом, изготовленный на заказ по индивидуальному заказу OEM, модульный Z-образного типа.

Сценарии применения

Часто задаваемые вопросы

What can be customized?

The layout, window and door positions, wall finish and electrical set out of a custom z type folding container house all follow your drawing. It is offered as custom OEM.
How does a flat packed unit arrive?

It comes as a flat pack of frame, panels and fittings, taking less space in transit and storing easily until you need it.
Is the wiring done in the factory?

Yes. Cable, sockets, lights and a breaker board are fitted and tested before the pack closes. On site you only connect the feed.
Does it need a crane to lift?

Four corner castings take the lift, and the pack lands on pads set level. The walls then swing up and pin at the corners.
What sort of project takes this unit?

Site offices, worker housing, clinics and small shops. A custom plan lets one shell work for several different jobs.

Текущий язык

Изменить язык