Folding Container House Custom OEM Z Type Flat Packed

Span, Packed Depth and Ordered Mass

Open, a custom z type folding container house measures 5,800 mm by 2,500 mm, and the pad has to carry that footprint exactly. That is about 14.5 m² of floor, with 2,430 mm of internal height, so a standing adult clears the ceiling. Folded, the pack sits 390 mm deep and stacks on a flat rack. Weight runs 1,100 kg on a standard build and 1,180 kg when the panel order gets thicker. The crane, the lorry and the pad all follow from those numbers.

Przedmiot	Standardowa wersja	What an OEM order can move it to	Fixed at
Ślad stopy	5800 × 2500 × 2430 mm	Length 5800 to 6000 mm, width to 2500 mm only	Steel cut
Folded thickness	390 mm	430 mm if walls go to 75 mm, which costs one set per 40HQ	Laminowanie paneli
Unit weight	1100 kg	1180 kg with a 75 mm core, 1040 kg with EPS	Laminowanie paneli
Sekcja ramy	Kolumna 63 × 80 × 1,5 mm	2.0 mm wall on the six folding posts only	Tube mill
Kolumna	150 × 62 × 1.5 mm U-groove	2.0 mm, or 160 mm depth for a second storey	Steel cut
Rdzeń ściany	Wełna mineralna 50 mm o gęstości 65 kg/m³	75 mm wool, EPS at 12 kg/m³, or PU at 40 kg/m³	Laminowanie paneli
Skóra ścienna	0,28 mm stal kolorowa	0.35 mm, wood grain, matte, or a printed wrap	Coil order
Dach	1040 tile 0.45 mm, 30 mm wool	75 mm roof panel, or a standing seam profile	Coil order
Podłoga	15 mm MGO, 1.6 mm wear layer	18 mm cement board, SPC, or a plywood deck	Panel layup
Drzwi	970 × 1970 mm aluminium anti-theft	840 × 2030 z zamknięciem lub podwójnym skrzydłem	Frame weld
Okna	2 × 870 × 1215 mm przesuwne	3 or 4 openings, awning, fixed, or full height	Frame weld
Elektryka	1 breaker, 3 sockets, 5 LED lights	Circuit split, 110 or 220 V, external inlet	Wiring
Insulation value	About R 1.3 for the 50 mm wall	R 1.9 at 75 mm, R 2.1 with 50 mm PU	Laminowanie paneli
Kolor	Jedna powłoka proszkowa RAL	One colour as standard, two tones when ordered	Powder coat
Cechowanie	Tylko znaki wysyłkowe	Numbers stencilled for routing across a site	Uszczelka
Dokumenty	Faktura, lista pakowania, B/L, CO	Paperwork that clears customs without a delay	Before loading
Minimum run	1 jednostka	10 units for a dedicated lamination run	Order
Czas realizacji	15 to 20 days	25 to 30 days once the coil is ordered	Coil order

Installation video

Tube Sizes, Panel Skin and Core

Square tube comes in two wall thicknesses, 2.0 mm on the main beams and 1.5 mm through the cross members and braces. A 160 mm sill beam carries the floor deck. At each corner stand 100 mm posts. Hinge barrels run stainless and bolt through a 200 mm plate. Every tube end gets capped and sprayed with cold galvanizing before paint.

Chassis schedule
· 2.0 mm galvanized main beam along each long side
· 1.5 mm cross members under the floor deck
· 160 mm sill beam with a folded top lip
· 100 mm corner posts, four to a unit
· 200 mm hinge plate in stainless steel

Outside, a custom z type folding container house carries 0.28 mm colour steel, with a 0.35 mm liner facing the room. A 50 mm core sits between them, bonded across the full face with a two part adhesive. Roof panels follow the same build, and the floor deck is 15 mm board. Panel edges fold into a lip that takes a gasket. Two people carry one finished panel by hand.

Panel and deck build
· 0.28 mm steel skin on the outer face
· 0.35 mm liner on the room side
· 50 mm insulated core, bonded full face
· 15 mm floor deck under a wear sheet
· Folded edge with a rubber gasket seat

Main Board, Ceiling Lights and Sockets

Wiring runs through the panel voids and terminates at marked boxes. Inside sit a main switch, an earth leakage trip and spare ways for the circuits that will be added later on site. Lamps and sockets sit on separate circuits. Heights for every switch follow the drawing agreed at order. An outside socket and a light over the door can join the same loom.

Zestaw elektryczny
· Distribution board with spare ways
· Leakage trip on the socket ring
· Ceiling lamps on a switched circuit
· Wall sockets at drawing heights
· External light over the entry door Spare ways sit in the board for the circuits that will be added later on site, and an outside socket plus a light over the door can join the same loom.

Erection Steps and Site Labour Needs

Once the pack is on the pad, erection needs no crane. Four workers cut the banding, lift the roof frame and stand the long walls, with pins dropping into the corners behind them. Roof cams draw the seam closed. End panels slide into their channels, and the door is checked for swing. The drawing carries a crew through the next unit.

Crew hand tools
· Banding cutter and a rubber mallet
· Podger bar for the corner pins
· Spirit level for the pad
· Sealant gun and two spare nozzles
· Touch up paint in the RAL shade

Crate Packing, Export Papers and Field Use

Flat, a custom z type folding container house stacks into a 40HQ at 50 mm wall thickness. Timber cradles take each unit and film wraps the pack. For a long sea leg, desiccant bags go inside before the wrap closes. Lifting points stay clear of the film, so a crane hook can still reach them. Outside marking matches the packing list and the frame stencil.

Packing list
· Timber cradle under each corner
· Shrink film over the folded pack
· Desiccant bags inside the wrap
· Corner guards on the castings
· Packing list in a weatherproof pouch

Documents ride with a custom z type folding container house: invoice, packing list, bill of lading and certificate of origin. Mill certificates, test reports and stamped drawings can join an OEM order. At the plant, spares cover pins, roof cams, sash rollers and lock barrels. The same body takes work as an office, a spare room, a clinic bay or a staff cabin.

Przepływ produkcji warsztatowej

Wprowadzenie do fabryki

Jesteśmy profesjonalnym producentem specjalizującym się w prefabrykowanych domach kontenerowych, rozkładanych domach kontenerowych, składanych domach kontenerowych oraz mobilnych łazienkach prefabrykowanych. Projektujemy, produkujemy i eksportujemy modułowe rozwiązania mieszkaniowe dla hoteli, willi, biur, akademików, magazynów, warsztatów i placów budowy. Nasza fabryka zajmuje powierzchnię 50 000 metrów kwadratowych i znajduje się w Kantonie. Zapraszamy gości.

specyfikacje produktu	20 stóp
tworzywo	Stal ocynkowana, stal nierdzewna 304
materiał wypełniający	wełna mineralna, EPS i poliuretan
Zakres temperatur pracy	-30°C do +70°C
Personalizacja	panele ścienne, panele podłogowe, gniazdka elektryczne, meble, przyłącza wodne, szafki kuchenne, urządzenia sanitarne itp.
Lokalizacja fabryki	KANTON

Obsługiwane warunki wysyłki	EXW, FCA, FOB, CIF, DDP
Warunki płatności	T/T, L/C, inne warunki do negocjacji

Aktualny język

Zmień język

Składany kontenerowy dom OEM typu Z, pakowany na płasko

Opis produktu

Span, Packed Depth and Ordered Mass

Tube Sizes, Panel Skin and Core

Main Board, Ceiling Lights and Sockets

Erection Steps and Site Labour Needs

Crate Packing, Export Papers and Field Use

Przepływ produkcji warsztatowej

Wprowadzenie do fabryki

Scenariusze zastosowań

Często zadawane pytania

Pobierać

Powiązany produkt