Folding Container House Factory Direct Z Type Sandwich Panel

Panel Thickness, Weight and Floor Area

Wall panels are 50 mm thick, roof panels 30 mm, and a square metre of wall panel weighs about 11.5 kg, light enough for two people to carry one sheet by hand. Folded, a z type folding container house makes a shallow pack that loads on a flat bed. At 2,500 mm open width, the floor takes a desk bank and a table. Thicker panels add weight and insulation.

Layer	As we build it	What it does	If you halve it
Outer skin	فولاذ ملون بسمك 0.28 مم	Takes the weather and holds the paint colour	0.15 mm dents at a hand push
Skin coating	Zinc plus polyester topcoat	Corrosion barrier at cut edges	Cut edges rust inside one wet season
Adhesive	Two-part PU, 180 g/m²	Bonds skin to core across the full face	Skin delaminates above 60 °C surface
Core, walls	50 mm rock wool, 65 kg/m³	Fire grade, sound control and shape retention	40 kg/m³ wool sags over 2 m height
Core, roof	30 mm rock wool, 60 kg/m³	Insulation without adding roof depth	20 mm roof panel condenses on the ceiling
Inner skin	فولاذ ملون بسمك 0.28 مم	A cleanable face that hides the core	0.20 mm ripples between ribs
Panel edge	Folded lip, gasket channel	The joint that actually seals	A cut edge needs a trim and still leaks
Panel width	1150 mm nominal	Fits the 2500 mm module without a rip cut	A 1000 mm panel wastes 150 mm per wall
Panel weight	About 11.5 kg/m² at 50 mm	Two people carry one panel without a hoist	9 kg/m² feels light and sounds hollow
U value	0.80 W/m²K at 50 mm wool	Sets the heating and cooling load	1.3 W/m²K at 30 mm wool
Fire rating	Class A as an assembly	Insurance and port acceptance turn on this	B1 with EPS, rejected by some ports
Sound reduction	About 30 dB at 50 mm	Speech from the next room is muffled	24 dB, conversation carries
Service life	15 years with coating intact	Paint cycle rather than a panel swap	8 years if edges are left bare

Installation video

Skins, Core and the Roof Panel Difference

Outside, a sandwich panel folding house wears 0.28 mm colour steel under a zinc and polyester coat. A two part PU adhesive bonds skin to core across the whole face. The wall core is 50 mm rock wool at 65 kg density, the roof core 30 mm at 60 kg, that density keeping the wool from settling. A folded lip closes onto a gasket channel.

Skin and core parts
· Colour steel coil, zinc and polyester coat
· Two part PU adhesive
· 50 mm rock wool batt for walls
· 30 mm rock wool batt for roof
· Gasket channel on the long edge

Wall and roof panels differ in thickness alone. Roof depth costs headroom, so on a z type folding container house the roof takes 30 mm while the walls take 50 mm for sound. Cut to the drawing and labelled by wall, every panel is packed in order. One mislabelled panel slows the fold on site. Spare panels travel with the batch when the order asks.

Panel schedule
· 0.28 mm colour steel outer skin
· 0.28 mm inner skin, cleanable face
· 50 mm rock wool in the walls
· 30 mm rock wool in the roof
· Folded lip with a gasket channel

U Value, Sound and Fire Behaviour

U value of 0.80 W comes off a 50 mm wall panel, and that one number sets the heating load for the whole room. Sound reduction reaches about 30 dB, enough to muffle speech from the next room. Class A fire rating counts twice here, at insurance and at port acceptance. Service life runs to 15 years with the coating kept whole. Repainting, not replacement, is the usual cycle.

Repair kit
· Touch up paint in the RAL batch
· Spare gasket in a coil
· Sealant cartridge for the joint
· Rivet set for the trim
· Panel lifting straps Class A fire rating counts twice here, at insurance and at port acceptance. Service life runs to 15 years with the coating kept whole, and repainting, not replacement, is the usual cycle on a z type folding container house.

Frame Tubes That Carry the Panels

Frame tube runs 1.5 mm, welded into a rectangle over a 150 mm sill, with posts standing at the corners and at every panel joint, so no panel carries load. The deep floor beam spreads the load. Hinges run stainless, through a folded plate. Every cut end gets a cold galvanizing spray before it sees paint.

Frame members
· 1.5 mm galvanized square tube
· 150 mm sill beam under the deck
· Deep floor beam on the long side
· Corner posts at four points
· Stainless hinge with a folded plate

Distribution Board, Sockets and Ceiling Lights

Inside the entry wall, a z type folding container house carries its board, with a main breaker and a leakage trip. LED ceiling lights split across two switches. Sockets sit at desk and bench height, per the drawing. Cable is pulled through the panel void before the skins close. An external light and a socket can be added at the order stage.

مجموعة كهربائية
· Lockable board with a main breaker
· Leakage trip on the socket ring
· LED ceiling lights on two switches
· Sockets set to the drawing schedule
· Lamp over the entrance

Delivery, Spare Parts and Service Life

On a flat bed, packs ride to the dock, and a 40HQ takes a stack plus the door and window cartons. Each unit is cradled, filmed and packed with desiccant. Spares cover gaskets, hinge pins, cam locks and window rollers. As an office, a store, a treatment room or a bunk room, the z type folding container house fits. Coating care is what carries the unit toward 15 years.

تدفق الإنتاج في ورشة العمل

مقدمة المصنع

نحن شركة تصنيع متخصصة في المنازل الجاهزة المصنوعة من الحاويات، بما في ذلك المنازل القابلة للتوسيع والطي، بالإضافة إلى الحمامات الجاهزة المتنقلة. نقوم بتصميم وإنتاج وتصدير حلول سكنية معيارية للفنادق والفلل والمكاتب والمساكن الطلابية والمستودعات وورش العمل ومواقع البناء. يمتد مصنعنا على مساحة 50,000 متر مربع ويقع في مدينة قوانغتشو. نرحب بزيارتكم.

مواصفات المنتج	20 قدمًا
مادة	الفولاذ المجلفن، الفولاذ المقاوم للصدأ 304
مادة الحشو	الصوف الصخري، والبوليسترين الموسع، والبولي يوريثان
نطاق درجة حرارة التشغيل	من -30 درجة مئوية إلى +70 درجة مئوية
التخصيص	ألواح الجدران، ألواح الأرضيات، مقابس الكهرباء، الأثاث، مداخل المياه، خزائن المطبخ، الأدوات الصحية، وما إلى ذلك
موقع المصنع	قوانغتشو

شروط الشحن المدعومة	EXW، FCA، FOB، CIF، DDP
شروط الدفع	شروط الدفع: تحويل مصرفي، خطاب اعتماد، شروط أخرى قابلة للتفاوض

اللغة الحالية

تغيير اللغة

منزل حاويات قابل للطي من المصنع مباشرة، لوحة ساندويتش من النوع Z

وصف المنتج

Panel Thickness, Weight and Floor Area

Skins, Core and the Roof Panel Difference

U Value, Sound and Fire Behaviour

Frame Tubes That Carry the Panels

Distribution Board, Sockets and Ceiling Lights

Delivery, Spare Parts and Service Life

تدفق الإنتاج في ورشة العمل

مقدمة المصنع

سيناريوهات التطبيق

التعليمات

تحميل

المنتج ذو الصلة